NMEA 2000 Components

The Garmin NMEA 2000 Starter Kit comes with all of the parts you need to start a NMEA2000 Marine Network.

Garmin’s GPS24XD NMEA2000 GPS antenna provides multi-band GNSS accuracy to 1M. The magnetic heading sensor provides accuracy to within 3 degrees with enhanced stabilization at slow speeds. Includes under-deck, pole and surface mount options.

The DST810 is a plastic thru-hull smart sensor that will provide digital depth(numbers only), speed and temp to any existing NMEA 2K network.

The Garmin NMEA 2000 T-Connector is required for adding components to your network. It is installed on the backbone cable and uses one end of the T-Connector for the drop cable.

Garmin NMEA 2000 Multiport T-Connector.

The Actisense NMEA 2000 to USB Dual Gateway Converter is equipped with a USB cable to allow Plug and Play connectivity with a PC. The NGX-1-USB cable provides an easy way to link a PC to a NMEA 2000 network. NMEA 2000 compliant software applications can read from and write to the NMEA 2000 Bus while maintaining network safety.

This Maretron cable can be used as your NMEA 2000 backbone or drop cable. Length 0.5 meter.

The Maretron NMEA 2000 T-Connector is a required part when adding components to your NMEA 2k network. It is installed on the backbone cable and uses one end of the T-Piece for the drop cable.

The Navico NMEA 2000 Starter Kit includes all of the parts neccessary to create a NMEA2000 Network on your boat.

This cable can be used as your NMEA 2000 backbone or drop cable. Length 2 Meter

The Garmin GFS 10 Fuel Sensor provides fuel flow and fuel level measurement data. You can view this information on your compatible Garmin NMEA2000 compliant chartplotter, GPS/FF combo or GMI 10 display.

This Maretron cable can be used as your NMEA 2000 backbone or drop cable. Length 6 Meter.

The Maretron NMEA 2000 Field Attachable Male Connector is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

The Actisense 4-port self-contained NMEA 2000 network makes installing a NMEA 2000 system easier than ever. The SBN-1 is a complete 4-port NMEA network that includes built-in termination resistors. Simply attach the integrated 3-meter power cable to the boats power supply and you are ready to add your devices!

The LinkUp J1939 provides an easy way to bridge CAN engine data transmitted through J1939 to the NMEA 2000 standard. The LinkUp device is NMEA 2000 compliant making vessel and engine data available for any NMEA 2000 capable display. Configuration is simple with the LinkUp Configurator App.

This Maretron cable can be used as your NMEA 2000 backbone or drop cable. Length 1 Meter.

This Maretron cable can be used as your NMEA 2000 backbone or drop cable. Length 3 Meter

The Maretron NMEA 2000 Power-Tee is used to power your NMEA 2K network and measures 5 meters in length. 

The DT820 is a flush mount, plastic thru-hull smart sensor that will provide digital depth(numbers only) and temp to any existing NMEA 2K network.

The Garmin NMEA 2000 Male Terminator is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

This Garmin cable can be used as your NMEA 2000 backbone cable. Length 10 Meter. This cable can not be used as a drop cable.

The Maretron NMEA 2000 Field Attachable Female Connector is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

This Maretron cable can be used as your NMEA 2000 backbone cable. Length 10 Meter. This cable can not be used as a drop cable.

Maretron is known for their high quality and durable NMEA 2000 parts, this starter kit includes: 2 T connectors, Powertap T, 2 Male Terminators, 1m Drop/Backbone Cable, and a 6m Drop/Backbone Cable. Everything you will need to start your NMEA 2K Network.

This Garmin cable can be used as your NMEA 2000 backbone or drop cable. Length: 6 Meters (19 feet).

Garmin's SteadyCast Heading Sensor offers a simple solution to heading accuracy. Easy to Install with a 10Hz output rate and accuracy to +/- 3°

Garmins 9 Axis Heading Sensor provides accuracy +/- 2°. 10Hz Output Rate ensures your chart orientation and boat heading is accurate with reality. Premium Heading Accuracy at low speeds and even when bow is pitching, rolling or heeling over.

The Raymarine STng (Male) to DeviceNet (Female) snap-on spur adaptor allows for easy connection to NMEA2000 devices.

The Actisense W2K-1 is a NMEA 2000 to Wi-Fi Gateway which transfers data from a NMEA 2000 backbone to any device (e.g laptop, tablet or smartphone) connected to it via Wi-Fi.

The VMH-35 D is specifically designed to help monitor diesel engines. This compact display is capable of showing a wide range of data from your engine, battery tank and GPS. With an embedded high-performance GPS and Analog/CAN to NMEA 2000 gateway- it is an ideal addition to your marine suite or as a standalone solution!

The Veratron GO Plus GPS module is a combined GPS/GLONASS/Galileo receiver and NMEA 2000 to Bluetooth gateway. The GO is the smallest NMEA 2000 GNSS antenna on the market with a 60.7mm diameter and small installation footprint. This 10Hz GPS receiver’s cold-start position fix is a mere 30 seconds making it a very high sensitivity GPS receiver!

Furuno GP330B NMEA2000 GPS Receiver is designed for pinpoint accuracy with your Furuno NavNet 3D or TZtouch Display. NMEA 2000 Network Required when installing without DRS Radar.

A NMEA 2000 Female Terminator is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

The Maretron NMEA 2000 Male Terminator is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

The DT812 is a flush mount, plastic thru-hull smart sensor that will provide digital depth(numbers only) and temp to any existing NMEA 2K network.

The Garmin NMEA 2000 Power Cable is used to power your NMEA 2K network through a standard NMEA2000 T-Connector.

The Garmin NMEA 2000 network updater provides the convenience of updating Garmin products and NMEA 2000 accessories that do not have an SD card slot.

The Garmin NMEA 2000 Female Terminator is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

The Maretron NMEA 2000 Micro Inline Terminator can be used at the end of a NMEA 2000 backbone to terminate the backbone and still allow for a single device to be used after the terminator.

The PG-700 Integrated NMEA 2000 Heading Sensor is a rate compensated heading sensor that incorporates innovative electromagnetic compass technology for highly accurate and stable readouts of your ship's heading.

Lowrance 4-Way NMEA 2000 Block is the perfect solution when networking and multiple drop cables are in close proximity. No need for multiple T- Connectors, offers a more cost effective and streamlined solution. Part # 000-12612-001 replaces part # 000-10996-001.

This NMEA 2000 P79 In Hull (up to 22 degree deadrise) smart sensor provides digital depth to any existing NMEA 2000 network. The P79 includes a 6 Meter NMEA 2000 cable and NMEA 2000 T Connector.

The Navico NMEA 2000 T-Connector is required for adding components to your network. It is installed on the backbone and uses one end of the T-Connector for the drop cable.

The Raymarine DeviceNet (Male) to STng (Female) snap-on spur adaptor allows for easy connection with NMEA2000 devices.

The Actisense 8-port self-contained NMEA 2000 network makes installing a NMEA 2000 system easier than ever. The SBN-2 is a complete 8-port NMEA network that includes built-in termination resistors. Simply attach the integrated 3-meter power cable to the boats power supply and you are ready to add your devices!

This Maretron cable can be used as your NMEA 2000 backbone or drop cable. Length 2 Meter.

The Actisense NMEA 2000 Field Fit Male Connector is used to begin or end the NMEA 2000 Backbone. It should be installed on one side of a Micro-Tee.

The Actisense 10 Meter NMEA 2000 cable can be used to extend your NMEA 2000 backbone cable. This cable can not be used as a drop cable.